Quantum Route

Quantum Route 3d design and manufacture. Hobby model builder/Painter
Pc water-cooling enthusiast

This kit is definitely doing a number on my hands (made especially difficult due to thumb issues 👍🏻) but by god, is it w...
11/12/2025

This kit is definitely doing a number on my hands (made especially difficult due to thumb issues 👍🏻) but by god, is it worth it.

The 4 'wings' have consumed a fair amount of time, and a large amount of parts! The thought and engineering that's gone into it is staggering though.

Downsides are mainly due to the instructions, and sadly it's simple things that should have been picked up in proof reading. Mislabeled parts being a main one, another being very dull diagrams so it's hard to make out placements at times, so common sense is a must.👍🏻

The chest led wires have no need being the length they are, and they are a nightmare to route due to the length, which is 'excessive' 💀

Other than that, I'm thoroughly enjoying the build, the wings should be attached today and hopefully get some armour started 😁😁😁

Progress! Yesterday I finally got started on the new Dominator model, and it's been an enjoyable (if somewhat painful on...
09/12/2025

Progress!
Yesterday I finally got started on the new Dominator model, and it's been an enjoyable (if somewhat painful on the hands) experience so far, and I'm thoroughly impressed. There has been nothing I've needed bar my trusty nippers and glass file
The instructions do have a couple of errors so that's been fun to figure out at times.
More progress updates as I get further through it 😊😊

Over the next few days, I receive a package that I cannot wait for, and have had my eyes on since it was unveiled, the A...
07/12/2025

Over the next few days, I receive a package that I cannot wait for, and have had my eyes on since it was unveiled, the Axis Model 1/100 Osiris Aerial Dominator.

The picture below shows just the sheer amount of parts in store for me, and I honestly can't wait.

Before that though, time to get this Seven Sword panel lined and decaled up 😬

Well, this has been a fun one to completeThe Daban Fat Cat 01 RGU 2.0 1/100 scale RX-78-2 does not disappoint, especiall...
05/09/2025

Well, this has been a fun one to complete

The Daban Fat Cat 01 RGU 2.0 1/100 scale RX-78-2 does not disappoint, especially for it's price and quality.

Tolerances at times are very tight, but overall not a bad build experience. There are also extra parts not pictured including a beam spear weapon, extra core fighter, extra rocket launcher & spiked ball with chain weapon.

Very pleased with the finished result, and now to wait for the final piece to arrive before displaying properly.

Next, I think we may have to look at something a bit taller 😬

Couldn't have agreed more
04/09/2025

Couldn't have agreed more

On to the final part of the Daban Fat Cat RG 2.0 1/100 scale Gundam RX-78-2, the water slide decals.....I've got to say,...
04/09/2025

On to the final part of the Daban Fat Cat RG 2.0 1/100 scale Gundam RX-78-2, the water slide decals.....

I've got to say, through the whole built process, the new nippers and glass file have made a huge difference when it's came to clean up, so check out to grab your own 👍🏻

Up until this point, I've managed to avoid water transfers as most have been dry transfer, so it's been a bit daunting, but I don't think I've done bad at all so far 😬

Onto the torso next, wish me luck 🤞🏻🤞🏻

He's a bit of a sexy goth beast.Some of these bootleg Ali express kits are impressive I have to admit.Still unsure if I'...
21/08/2025

He's a bit of a sexy goth beast.

Some of these bootleg Ali express kits are impressive I have to admit.

Still unsure if I'm going to add the decals 🤔

With Stedi Tool – I just got recognised as one of their top fans! 🎉
04/08/2025

With Stedi Tool – I just got recognised as one of their top fans! 🎉

Before I started on my next project, I decided to tackle the main issue most Gunpla and similar model builders. Sprue bu...
25/07/2025

Before I started on my next project, I decided to tackle the main issue most Gunpla and similar model builders. Sprue bubs being everywhere!

Thanks to Shadom1102 on Makerworld (links below) for designing this build surface designed to collect all those pesky nibs!

It also comes with inserts for magnets to connect multiple together in a sort of modular design.

It is a large area print though, with brim it fills an A1/P1P bed 😬

There are also a few bits coming from Stedi Tool ready for the next build, as well as paints, which as always, are from Vallejo.

Watch this space, I'm not even going to announce which model it is and people can guess 😂

Designer link: https://makerworld.com/
File link: https://makerworld.com/models/521581

Shenlong is assembled! Another to add to the MG Endless Waltz range I'm amassing (I do love the Gundam Wing era) Now ont...
23/07/2025

Shenlong is assembled!
Another to add to the MG Endless Waltz range I'm amassing (I do love the Gundam Wing era)
Now onto panel lining, a bit of clean up, and the decals 🙂

I'm also moving over the next few weeks, so hopefully in the near future, there should be a lot more content and videos 💪🏻

Stay tuned to see the finished product and to find out what's next on the build table 🤘🏻 a lot more in the way of custom painting with the next model 😬



Address

Seaham

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm
Saturday 9am - 5pm

Telephone

+447375901791

Website

Alerts

Be the first to know and let us send you an email when Quantum Route posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Quantum Route:

Shortcuts

Share

Category