All Engineering Hub

All Engineering Hub Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from All Engineering Hub, Delhi, Delhi.
(7)

DM me for Promotion 💌
[email protected]
Follow my Backup page👇🏻
https://www.facebook.com/share/1NEKYJCwWA/

Join our telegram channel 👇🏻
https://t.me/EngineeringTips1

🦋 *BUTTERFLY VALVE: Parts + Types Explained* 🦋*Key Parts:**Body:* Main valve housing, fl**ged or wafer type *Disc:* Rot...
11/05/2026

🦋 *BUTTERFLY VALVE: Parts + Types Explained* 🦋

*Key Parts:*
*Body:* Main valve housing, fl**ged or wafer type
*Disc:* Rotating plate that controls flow
*Stem:* Upper shaft connects disc to actuator
*Seat:* Soft or metal seal for zero leakage
*Bushings + Pins:* Support stem and disc alignment
*Lining:* Protects body from media corrosion

*Actuation Options:*
*Lever:* Quick manual open/close
*Gearbox + Handwheel:* Precise control for large valves
*Pneumatic/Electric Actuator:* For automation + DCS control

*Rule:* Quarter turn = full open to close. Select seat material based on media, temp, pressure. Wrong seat = leakage + valve damage.

*Save for piping, instrumentation + maintenance engineers.*

🦋🔧

💧 *WHY FL**GE JOINTS LEAK: 9 Hidden Causes* 💧*Top Reasons for Failure:*1. *Poor surface condition:* Scratches, pitting o...
11/05/2026

💧 *WHY FL**GE JOINTS LEAK: 9 Hidden Causes* 💧

*Top Reasons for Failure:*
1. *Poor surface condition:* Scratches, pitting on fl**ge face
2. *Wrong gasket:* Material not matching temp, pressure, media
3. *Uneven bolt load:* Wrong torque sequence or value
4. *Thermal cycling:* Expansion + contraction loosens joint
5. *Misalignment:* Pipe stress on fl**ges
6. *Gasket crushing:* Excessive torque damages gasket
7. *Bad lubrication:* Wrong l**e or crusting on bolts
8. *Vibration:* Dynamic loads relax bolt tension
9. *Poor assembly:* Dirt, reused gasket, wrong fit-up

*Key Checks:* Seal integrity, correct torque, alignment, regular inspection, proper lubrication.

*Rule:* Leaks cost safety + money. Torque in star pattern. Never reuse gaskets. Match gasket to service conditions every time.

*Save for piping, maintenance + reliability engineers.*

💧🔩

🌊 *CORIOLIS MASS FLOW METER: Measure Mass, Not Just Volume* 🌊*How It Works:**Sensor Tubes:* Vibrate as fluid flows throu...
11/05/2026

🌊 *CORIOLIS MASS FLOW METER: Measure Mass, Not Just Volume* 🌊

*How It Works:*
*Sensor Tubes:* Vibrate as fluid flows through
*Coriolis Force:* Creates phase shift proportional to mass flow
*Pick-off Coils:* Detect phase shift for flow rate
*Density Measurement:* Tube frequency changes with fluid density

*Key Specs:*
*Output:* 4-20mA / HART for DCS/PLC
*Power:* 24V DC
*Material:* 316L SS wetted parts, -40 to +150°C, up to 40 bar
*Display:* Direct mass flow kg/h, density, temperature

*Advantage:* Measures mass flow directly. No temperature, pressure, or viscosity compensation needed. Handles liquids, gases, slurries.

*Rule:* Keep tubes full + no entrained gas for accuracy. Zero calibrate with no flow. Mount vertical for liquid, horizontal for gas.

*Save for instrumentation, process + custody transfer engineers.*

🌊📊

11/05/2026

⚡ *KW TO AMPERE: Quick 3-Phase Motor Formula* ⚡

*Example Problem:*
*Motor Power:* 75 kW
*Voltage:* 440V
*Power Factor:* 0.9
*Find:* Full Load Current

*Formula (3-Phase):*
*I* = (kW × 1000) / ( $\sqrt{3}$ × V × PF)

*Solution:*
*I* = (75 × 1000) / (1.732 × 440 × 0.9)
*I* = 75000 / 685.872
*I = 109.34 Amperes*

*Rule:* Always use line voltage for 3-phase. Check motor nameplate PF. Add 25% safety margin for cable + breaker sizing.

*Save for electrical, maintenance + panel engineers.*

⚡🔌

⚙️ *6300 SERIES BEARING: Size Chart + Quick Facts* ⚙️*What Is It:*Single row deep groove ball bearing for high speed, lo...
11/05/2026

⚙️ *6300 SERIES BEARING: Size Chart + Quick Facts* ⚙️

*What Is It:*
Single row deep groove ball bearing for high speed, low to medium load

*Key Sizes (ID × OD × Thickness):*
*6305:* 25mm × 62mm × 17mm
*6308:* 40mm × 90mm × 23mm
*6310:* 50mm × 110mm × 27mm

*Easy Rule:* Last two digits × 5 = ID in mm
*Example:* 6305 → 05 × 5 = 25mm ID

*Quick Facts:* High radial load, low noise, long life
*Used In:* Motors, pumps, fans, gearboxes, machines

*Rule:* Always match ID, OD, and thickness. Check suffix like 2RS for seal and C3 for clearance. Wrong size = shaft damage + downtime.

*Save for maintenance + machine shop engineers.*

⚙️📏

📊 *FLOW NOZZLES: Smart DP Flow Measurement* 📊*Key Benefits:**High Velocity Design:* Handles steam, gas, high temp fluids...
11/05/2026

📊 *FLOW NOZZLES: Smart DP Flow Measurement* 📊

*Key Benefits:*
*High Velocity Design:* Handles steam, gas, high temp fluids
*Minimal Pressure Loss:* Saves pumping energy vs or***ce
*Greater Wear Resistance:* Long life in abrasive service

*Install Distances:*
*HP Tap:* 1D Upstream from nozzle inlet
*LP Tap:* 0.5D Downstream from nozzle outlet
*Standard:* ISO 5167 Compliant

*Nozzle vs Or***ce Plate:*
*Rounded Inlet:* Reduces turbulence, pressure loss, and wear
*Or***ce Plate:* Sharp edge = more wear + higher permanent loss

*Rule:* Maintain straight run and correct tap distances. Wrong installation = inaccurate flow reading. Use nozzles for high velocity and erosive fluids.

*Save for instrumentation + process engineers.*

***ceVsNozzle 📊💧

🪛 *DRILL TAP SIZE FORMULA: No More Guesswork* 🪛*Quick Formulas:**Metric:* Tap Drill Size = Major Diameter - Pitch *Exam...
11/05/2026

🪛 *DRILL TAP SIZE FORMULA: No More Guesswork* 🪛

*Quick Formulas:*
*Metric:* Tap Drill Size = Major Diameter - Pitch
*Example:* M10 × 1.5 → 10 - 1.5 = *8.5mm drill*

*Inch UNC/UNF:* Tap Drill Size = Major Diameter - 1/TPI
*Example:* 1/4" - 20 UNC → 0.250 - 0.050 = *0.200 inch = #7 drill*

*Important Tips:*
Too small = tap breaks. Too large = loose threads. Always use cutting fluid for clean threads.

*Rule:* Right drill size makes perfect threads. Check chart or formula before drilling every time.

*Save for fitters, machinists + toolroom teams.*

🪛⚙️

11/05/2026

🔄 *PULLEY RPM CALCULATION: Quick Exam Formula* 🔄

*Given Data:*
*Motor RPM:* 1440
*Motor Pulley Dia:* 10 mm
*Pump Pulley Dia:* 12 mm

*Formula:*
*Pump RPM* = (Motor RPM × Motor Pulley Dia) / Pump Pulley Dia
= (1440 × 10) / 12
= 14400 / 12
= *1200 RPM*

*Concept:* Bigger driven pulley = lower speed, higher torque. Smaller driven pulley = higher speed, lower torque.

*Rule:* Driver Dia × Driver RPM = Driven Dia × Driven RPM. Always check belt slip + alignment in real systems.

*Save for mechanical students, fitters + maintenance teams.*

🔄⚙️

🔧 *CONTROL VALVE STATION: Safety + Flow in One Loop* 🔧*Valve Functions:**Control Valve:* Regulates flow, pressure, tempe...
11/05/2026

🔧 *CONTROL VALVE STATION: Safety + Flow in One Loop* 🔧

*Valve Functions:*
*Control Valve:* Regulates flow, pressure, temperature, level
*U/S + D/S Isolation:* Block valves to isolate control valve for maintenance
*Bypass Valve:* Keeps line running during control valve failure/service
*Block Valve:* Isolates pipeline sections for safety
*Emergency Isolation Valve (EIV):* Quick shut-off in emergency

*Why This Setup:*
*Safety:* Safe isolation + emergency shutoff
*Efficiency:* Optimized process performance
*Maintenance:* Service control valve without plant shutdown
*Reliability:* Continuous operation with bypass option

*Rule:* Never operate control valve without U/S + D/S isolation valves. Always close isolation valves before removing control valve. Bypass only for emergency or maintenance.

*Save for piping, instrumentation + process engineers.*

🔧💧

⚙️ *BEARING OD FORMULA: Know Your Dimensions* ⚙️*Key Facts:**ID Rule:* Last two digits × 5 = Inner Diameter *Example:* ...
11/05/2026

⚙️ *BEARING OD FORMULA: Know Your Dimensions* ⚙️

*Key Facts:*
*ID Rule:* Last two digits × 5 = Inner Diameter
*Example:* 6305 → 05 × 5 = *25mm ID*
*OD Truth:* No direct formula. OD depends on bearing series

*Series Wise Comparison - Same ID, Different OD:*
*6205:* 25mm ID × *52mm OD* × 15mm thick
*6305:* 25mm ID × *62mm OD* × 17mm thick
*6405:* 25mm ID × *80mm OD* × 21mm thick

*How To Find OD:*
1. Get bearing number
2. Last two digits × 5 = ID
3. Check series from first two digits
4. Use series chart for OD + thickness

*Rule:* Same ID can have different OD + thickness. Series matters. Always check load, speed, application before selection. Wrong OD = fitment issue + downtime.

*Save for maintenance, fitters + machine shop teams.*

⚙️📏

🔨 *HAMMER ANATOMY: Every Part Has a Job* 🔨*Key Parts:**Face:* Hardened steel striking surface for nails *Claw:* Pulls n...
11/05/2026

🔨 *HAMMER ANATOMY: Every Part Has a Job* 🔨

*Key Parts:*
*Face:* Hardened steel striking surface for nails
*Claw:* Pulls nails, rips boards, demolition work
*Cheek:* Side of hammer head for strength
*Neck:* Connects head to handle, absorbs shock
*Eye:* Hole where handle locks into head
*Handle:* Fiberglass/wood for leverage + control
*Grip:* Rubberized anti-slip for safety

*Rule:* Strike with the face only. Never use cheek or claw for hitting. Check handle for cracks before use. Loose head = serious injury.

*Save for carpenters, fitters + site workers.*

🔨🪚

Address

Delhi
Delhi

Telephone

+918882117208

Website

https://amzn.to/4tmPjtp

Alerts

Be the first to know and let us send you an email when All Engineering Hub posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share