09/06/2025
UNDERSTAND THE CHECK ENGINE LIGHT,CAUSES, TROUBLESHOOTING AND COMMON DTC CODES
Your vehicle performs hundreds of operations in order to get you from point A to point B safely, efficiently, and in comfort. It relies on an array of on-board computers, sensors, and other components that are in constant communication with each other to control and monitor vehicle functions. All of that complexity can make it difficult to diagnose when something goes wrong.
Fortunately, modern automobiles include a system of self-diagnosis. When a problem pops up, your vehicle knows it – and it lets you know. One way it does so is by turning on the check engine light.
THE ENGINE CONTROL MODULE
The moment you turn the key or press a button to start your engine, your vehicle begins to perform a series of self-diagnostic tests to ensure everything is working according to plan. While it is running, the on-board computers continue to monitor vehicle functions. It is common for a modern vehicle to feature nearly a hundred small computers that work with the host of sensors and components to which they are related.
These computer control modules, for example, assess and adjust how much air and fuel are introduced to the cylinders or combustion chambers. They measure how much pollutant is coming out of the exhaust system and adjust accordingly. They sense when the oil is low, when the brake pads need to be replaced, and how much evaporated fuel from the tank needs to be recirculated back to the engine. Most every operation performed in your late model car, truck, or SUV is monitored and controlled by a computer control module.
Among the myriad computer control modules (sometimes called “control units”), the most significant is the engine control module, or ECM. The ECM is the master computer in charge of engine function and related issues. Depending on your vehicle manufacturer, this device might be referred to as an engine control unit (ECU) or powertrain control module (PCM). In any case, this mothership of computer control modules monitors and controls engine function and other related issues. It constantly performs diagnostic tests on vehicle systems, and whenever something goes wrong with the way your vehicle is running, it senses and stores information about the fault, and then it sends an alert signal to the driver that there is a problem.
THE CHECK ENGINE LIGHT
When something goes wrong with a vehicle, there are many alert signals that might be sent to a driver. These include messages on the electronic display about low tire pressure, or dashboard warning lights related to high engine temperature or low oil pressure. But the signal that causes the most concern for many folks is usually the check engine light, or CEL for short.
When the ECM detects a problem with a vehicle system – for instance, a sensor that is sending the wrong data or no data at all – it will store information that can later be accessessed by a repair technician. It will also turn on the check engine light to let you know that something is wrong. The issue could be something as simple as a loose gas cap, or it could be something as serious as an engine misfire. When you see the check engine light come on, you should know that it is time to take your vehicle to a technician for an accurate diagnosis.
IS THE CHECK ENGINE LIGHT SERIOUS?
The presence of a check engine light is often misunderstood because it bears many meanings. When it lights up, there is no knowing if the cause is a simple fix (like tightening up your gas cap) or a more grave problem that could damage your engine.
In fact, there are times when the check engine light might come on when there is nothing wrong with your vehicle at all. In those cases when a temporary condition is caused by environmental or other factors (a change in humidity, for example), the light should go off by itself after a short amount of time.
But if it stays on, the check engine light should not be ignored. And if it is blinking on and off – an indication of a serious condition in need of immediate attention – do not continue to drive your vehicle.
HOW LONG CAN YOU DRIVE WITH THE CHECK ENGINE LIGHT ON?
Although plenty of drivers ignore the warning lights on the dashboard, many find that their heart sinks a bit when the Check Engine Light comes on. If it does, there is no need for panic. Instead, pay attention to what you see, feel, and hear from your vehicle. If you do not detect a change in performance – no odd sounds, loss of power, vibration, or other sensation – you can simply take it to a qualified technician at your earliest convenience.
If, on the other hand, the check engine eight is blinking on and off, that is another matter entirely. Stop driving. Pull over in the nearest safe location and call a tow service to take your vehicle to a repair facility.
TOP 10 REASONS WHY A CHECK ENGINE LIGHT COMES ON
1. LOOSE GAS CAP
It might seem like a simple and almost comical reason, but a loose gas cap can actually cause your check engine light to come on. Your car’s fuel system is designed to be airtight, and when the gas cap is not properly sealed, it can lead to an incorrect fuel-to-air ratio that triggers the light. If this is the case, simply tighten or replace your gas cap and see if the light goes off.
2. FAULTY OXYGEN SENSOR
Your car’s oxygen sensor measures the amount of unburned oxygen in your exhaust system and helps regulate the fuel-to-oxygen ratio. A faulty sensor can cause your check engine light to come on and reduce your gas mileage, leading to a higher level of emissions. It’s important to have this sensor replaced promptly to avoid further engine damage and reduce your impact on the environment.
3. FAILING CATALYTIC CONVERTER
Catalytic converters are responsible for reducing harmful emissions from your car’s exhaust fumes. When it fails, not only can it cause your check engine light to come on, but it can also lead to decreased engine performance and increased pollution. If you notice a decrease in acceleration or an unusual smell from your exhaust, the catalytic converter may be the culprit.
4. MALFUNCTIONING MASS AIRFLOW SENSOR
The mass airflow sensor measures the amount of air entering your car’s engine and helps regulate fuel flow. When this sensor malfunctions, it can cause a variety of issues, including decreased gas mileage and engine performance. Ignoring the problem can lead to more severe engine damage, so be sure to address any issues with your mass airflow sensor as soon as possible.
5. FAULTY SPARK PLUGS OR WIRES
Spark plugs and wires are essential components in your car’s ignition system. When they fail, your car may have trouble starting, and the check engine light can come on as a result. Regularly checking and replacing these parts can prevent further damage and keep your car running smoothly.
6. WORN-OUT TIMING BELT
The timing belt is responsible for synchronizing the rotation of the crankshaft and camshaft in your car’s engine. When it becomes worn or damaged, your engine may misfire, leading to a check engine light warning. If left defective, a broken timing belt can cause significant and costly damage to your engine.
7. FAULTY IGNITION COIL
The ignition coil is responsible for supplying electricity to your car’s spark plugs, allowing them to ignite the fuel in the engine. When it fails, your car may experience issues with starting or acceleration, and the check engine light can come on as a result. Replacing a faulty ignition coil is relatively simple and can prevent further problems down the road.
8. LOOSE OR DAMAGED EXHAUST PIPE
If you hear a hissing noise coming from your exhaust system, it could be a sign of a loose or damaged exhaust pipe. A damaged pipe can cause your check engine light to come on and also lead to increased emissions and decreased fuel efficiency. It’s essential to have any issues with your exhaust system addressed promptly to avoid further damage and costly repairs.
9. LOW FLUID LEVELS
If your car’s fluid levels, such as oil, transmission fluid, or coolant, are running low, it can cause your engine to function improperly. This can trigger your check engine light and potentially lead to more severe engine damage if not addressed promptly. Regularly checking and topping off fluid levels is an essential part of car maintenance and can prevent costly repairs in the future.
10. ELECTRICAL ISSUES
Modern cars are heavily reliant on complex electrical systems to function correctly. If there’s a problem with any of these systems, such as the battery or alternator, it can trigger your check engine light warning. Have an expert perform a diagnostic test using a check engine light reader to pinpoint the exact issue and prevent potential breakdowns on the road.
DIAGNOSTIC TROUBLESHOOTING CODES
The on-board diagnostic system – referred to as “OBD-II” (a term that represents the second generation of on-board diagnostics) – uses an array of DTCs to alert a technician as to where the possible or probable cause of a problem might lie. The codes are accessed with a diagnostic scan tool that the technician will connect to a data port inside your vehicle.
DTCs are five-digit alphanumeric codes that fall into four different categories, depending on where a particular malfunction might be found. Each category is represented by a letter:
GENERIC CODES – These codes are common to all vehicles no matter who the manufacturer is. Generic codes are indicated with a “0” as the second digit (i.e. P0000).
ENHANCED CODES – On the other hand, enhanced codes are those that are manufacturer-specific and related to a specific (often outside the engine control system) vehicle applications. Enhanced codes are represented with a “1” as the second digit (i.e. P1000).
COMMON DTCs FOR A CHECK ENGINE LIGHT
There are literally thousands of different DTCs, many of which are widely used across all vehicle manufacturers, and many that are manufacturer- or vehicle-specific. The codes most often encountered during a diagnostic scan (and the most common causes of a check engine light) are the powertrain (P) codes. P codes are related to the function of most vehicle systems.
While there are far too many codes to list, below are descriptions of several P codes that are likely to come up when there is a problem with your vehicle. Following those descriptions is a list of DTCs with links to pages highlighting various DTCs, what they mean, how they might be caused, and the symptoms for which you might be on the lookout.
🔧:CODES P0171 THROUGH P0175
This set of codes is caused by the fuel system allowing either too much oxygen or too much fuel into the combustion chambers, resulting in an air/fuel ratio that is either too lean or too rich. These trouble codes specifically reveal the level of oxygen present in the system.
🔧:P0171 – This code lets a technician know that the system is running lean. In other words, your engine is receiving too much air. This can be caused by problems such as a leaking intake manifold gasket that allows too much air into the cylinders, or a faulty mass air flow sensor that sends an errant message to the Engine Control Module about how much air is entering the engine. A bad fuel pressure regulator can prevent a sufficient amount of fuel from reaching the engine, thereby throwing off the mix of air and fuel. Other possible causes include a weak fuel pump, clogged fuel filter, bad oxygen sensor, or a vacuum leak.
🔧:P0172 – This code signals a technician that the fuel system is causing your engine to run too rich. That means, the air/fuel mixture has too much fuel (or not enough air). This condition can also be caused by a faulty mass air flow sensor if it is sending the wrong information to the ECM. But it can also result from a bad fuel injector that refuses to shut off when it is supposed to, or even a dirty and clogged engine air filter that starves the engine of air. Other causes include a bad coolant temperature sensor, or a faulty engine thermostat.
🔧:P0173 – The ECM is constantly monitoring and adjusting the “fuel trim” to compensate for deviations from the optimal air/fuel ratio. When the ratio is too extreme for the ECM to compensate, whether too lean or too rich, a code P0173 will display. This code can be caused by a number of factors, including a leaking intake manifold gasket, malfunctioning mass air flow sensor, or severely clogged engine air filter. It can also be a result of a failed fuel pressure regulator that leads to low pressure at the fuel injectors.
🔧:P0174 – Whereas a code P0171 indicates a lean air/fuel mixture in “Bank 1” of an engine, this code signals a lean condition in “Bank 2”. Bank 1 is the side of an engine that houses Cylinder 1 (the first in the firing order). Bank 2 is on the opposite side of the engine. However, many vehicles on the road today feature four-cylinder engines that have only one bank. Causes of this code are the same as with P0171.
🔧:P0175 – This code is similar to a code P0172 but relates to a rich fuel condition in “Bank 2” rather than “Bank 1”. Gasoline powered engines want to run at an optimum air/fuel ratio, one that is most efficient and provides the most power. Problems that cause the ratio to vary in one direction or the other (too rich, in this case) can sometimes be corrected by the ECM. If not, you will see the Check Engine Light come on. A diagnostic scan will reveal the trouble code. From there, it is up to the technician to ascertain where the trouble may be found. The specific causes of a code P0175 are the same as those of code P0172.
Codes P0300-P0306
These are related to engine misfires that can be caused by a faulty fuel pump, bad fuel injectors, a blown cylinder head gasket, timing problems, or even fouled spark plugs. In fact, many issues can lead to a diagnostic trouble code in this category.
A misfire occurs when one or more of the cylinders in your engine fail to fire. That is, combustion does not occur the way it should. Your engine requires four conditions to fire properly: fuel, air, compression, and a source of ignition (the “spark”). If any of these are inhibited or out of sequence, a cylinder can fail to fire adequately (or at all). A rough idle, poor acceleration, hesitation, sudden loss of power, and other symptoms come as a result.
And your check engine light will likely come on.
The specific trouble code identified through a diagnostic scan will alert a technician to the cylinder in which the misfire occurs. Code P0300 suggests a misfire in multiple cylinders. Code P0301 tells of a misfire in cylinder 1. P0302 indicates that cylinder 2 is misfiring. And so on.
What this set of DTCs does not specify is the direct cause of the misfire. For that, a technician must investigate further.
COMMON CAUSES OF AN ENGINE MISFIRE INCLUDE:
🔧Fouled or damaged spark plug that produces a weak spark, one that is insufficient to set off combustion in a cylinder
🔧Faulty ignition coil that can also lead to a weak spark. This results in inadequate combustion
🔧Failed fuel pressure regulator or fuel pump that exhibits low pressure and causes the fuel injectors to malfunction
🔧Clogged or inoperative fuel injectors that do not allow enough fuel into a cylinder
Bad EGR valve that allows an incorrect amount of exhaust gas into a cylinder
🔧Leaking head gasket or intake manifold gasket can allow too much air to enter a cylinder, throwing off the air/fuel ratio and causing a misfire
This list is not comprehensive. There are many causes of engine misfire. Even a malfunctioning control module (computer) or sensor can prevent a component from working properly and lead to a misfire. If your Check Engine Light comes on and you notice signs of an engine misfire, make sure to have a technician accurately diagnose the problem.
🔧: Codes P0440, P0442, P0446, and P0455
This set deals with problems in the evaporative emission (EVAP) system that collects evaporated fuel from the fuel tank so that it is rerouted to the engine and does not escape into the atmosphere.
P0440 – This code stems from an EVAP system malfunction. More specifically, a leak. Common problems that can trigger this code (and your Check Engine LIght) are a loose or faulty gas cap, a leaking fuel evaporative canister, or a bad purge control valve. If the fuel filler neck or EVAP hose are punctured or the fuel tank is damaged, a code P0440 can also be triggered.
🔧: P0442 – The previous code (P0440) relates to a fairly large leak in the EVAP system. This code refers to a small leak that might be caught by the leak detection pump. And although the problem – stemming from the same general causes as the larger leak – might not show symptoms to the driver, it will still turn on the Check Engine Light.
🔧: P0446 – The EVAP system not only captures evaporated fuel vapors from the fuel system, it also stores those vapors to be used later, to be burned in the engine when called for. Those vapors are stored in a special EVAP canister and controlled by the purge control valve. This code has to do with a malfunction in the electrical circuit that contains the purge control valve. Other causes of this code include a missing gas cap, defective purge control valve, damaged fuel filler neck or fuel tank, or a bad sending unit.
🔧: P0455 – This code is reserved for an EVAP system malfunction designated as a “gross leak”, one that prevents the system from maintaining pressure. But this code can also indicate a lack of flow in the system. A stuck purge control valve can be the culprit. A bad fuel pressure sensor can also cause the code. So can blockages in the hoses or tubes in the system. And any of the aforementioned causes of a system leak can lead to this code if they are significant.
Codes P0400-P0408
These are among a set of DTCs related to a faulty exhaust gas recirculation (EGR) valve. Common codes in this series are P0401 and P0402, showing that the EGR flow is either insufficient or excessive.
🔧: P0401 – This code, reflecting a restricted EGR flow, can be caused by a restriction in the EGR passages, often as a result of a buildup of carbon. The problem could be a bad EGR valve or a faulty EGR valve cooler, each of which could restrict flow. But an improper data stream to the computer module from a related component could also be a problem, such as an EGR valve temperature sensor or MAP sensor that is malfunctioning.
🔧: P0402 – This code, on the other hand, suggests that the EGR system is seeing too much flow. A defective EGR valve could be the culprit here as well, only in this case, the valve is staying open rather than shut. Most of the components that can cause a P0401 code can also cause this one. But so can problems with other components, such as the MAP sensor, that send improper feedback related to the EGR system. Driving with the Check Engine Light on because of this code is not recommended.
Codes P0420 and P0430
Codes in this range suggest a problem with the catalytic converter in the exhaust system. The catalytic converter in your vehicle is there to break down harmful combustion byproducts before they exit the exhaust system. It does so by using platinum and gold components to create a chemical reaction that separates unsafe compounds from the exhaust gasses.
🔧: P0420 – This code is defined as “catalyst system efficiency below threshold (Bank 1)”. That means the catalytic converter is not functioning as it should. The way your vehicle determines whether or not the catalytic converter is doing its job is with a pair of oxygen sensors positioned before and after the converter in the exhaust stream. Those sensors read the amount of oxygen present in the exhaust and send data to the computer. A bad catalytic converter can trigger this code. But so can a faulty oxygen sensor that sends bad information to the computer. Another cause of this code can be a faulty mass air flow sensor that causes the engine to run either too lean or too rich.
🔧: P0430 – This code relates to the same problems as P0420 but in Bank 2, typically associated with larger engines (V6 or V8 engines, for example).
🔧: Code P0411 is another common code related to the exhaust system, only this time it suggests a problem with the secondary air injection system. This system is designed to reduce emissions by introducing fresh air into the exhaust stream. If an oxygen sensor detects too little oxygen in the exhaust, the CEL will come on.
P0411 – Common causes of this code include a bad secondary air injection pump filter or a leaking secondary air injection hose. The air injection pump itself can also be at fault.
COMMON OBD-II DTCs
P0000 Series
P0011 P0012 P0014 P0015 P0079
P0100 Series
P0100 P0101 P0102 P0104 P0105 P0112 P0113 P0115 P0116 P0117 P0118 P0120 P0122 P0123 P0124 P0128 P0130 P0131 P0132 P0133 P0137 P0138 P0170 P0171 P0172 P0174 P0175
P0200 Series
P0200 P0201 P0220 P0225 P0230 P0262 P0265 P0268 P0271 P0274 P0277 P0280 P0283
P0300 Series
P0300 P0301 P0302 P0303 P0305 P0335 P0351
P0400 Series
P0400 P0401 P0402 P0403 P0420 P0421 P0430 P0440 P0441 P0442 P0446 P0450 P0455 P0456 P0496
P0500 Series
P0500 P0505 P0506 P0507 P0520 P0561 P0562
P0600 Series
P0600
P0700 Series
P0700 P0703 P0705 P0706 P0715 P0720 P0730 P0745 P0750 P0755 P0760 P0780 P0781 P0782 P0783 P0784 P0785
P0800 Series
IN CONCLUSION
While seeing your check engine light come on can be a cause for concern, it’s important to remain calm and address the issue promptly. Ignoring warning signs can lead to more severe and costly engine damage in the future. By understanding these 10 common reasons why your check engine light is on, you can be better equipped to identify and resolve any potential issues with your car. Remember, regular maintenance and timely repairs are crucial for keeping your car running smoothly and efficiently.
