Strong Arm Porting & Cylinder Heads

Strong Arm Porting & Cylinder Heads Cylinder head rebuilding, repairs full porting and flow testing we focus on all things induction. If it drives,flys or rides we can help you out.

LT4 blower in for a make over it may not look like a lot of work but they are a lot of it is enlarging areas and transit...
11/08/2025

LT4 blower in for a make over it may not look like a lot of work but they are a lot of it is enlarging areas and transitions. This now has a massive Katech 103mm throttle body now fitted and a pvc delete.

Disassemble
Fully ported
Transitions blended on intake runner outlets
Snout enlarged to fit new TB
Remove old silicone and clean sealing surfaces
Final clean
Reassemble

Another bonus time laps of me cleaning

Have a great weekend guys stay safe especially if you’re in the bush.

Ford 3.0L heads in for an over haul they had very bad leak down. As it turned out the valves were pretty much toast and ...
10/31/2025

Ford 3.0L heads in for an over haul they had very bad leak down. As it turned out the valves were pretty much toast and needed to be replaced no margin was left.

Disassemble
Jet wash and Vapor hone
Dye penetrant test for cracks
Replaced 3 broken exhaust manifold studs and heli coiled
Multi angle valve job
Resurfaced
Final clean
Reassemble

Bonus clip of a time laps roughing out a set of 243 intake runners.

Have a great weekend guys!

370cc Bbc Victor rectangle port headsThese came bare pretty much a porters casting so lots of material to remove. Iv pos...
10/23/2025

370cc Bbc Victor rectangle port heads

These came bare pretty much a porters casting so lots of material to remove. Iv posted before and after flow numbers for those curious. Going on a 510ci drag engine. There’s about 45hrs of just port work and testing one thing to keep in mind these numbers will pick up as there’s no valve job completed yet. And this test was done on the shorter poorer intake runner vs the longer better runner but I can say without a doubt these are going to work well very happy with these gains.

Have a great weekend guys!

Looks sleepy 😴 and then I woke it up
10/18/2025

Looks sleepy 😴 and then I woke it up

Ls 823s for a 6.0L mud bog truck in for porting and rebuild. Been awhile since in the grinder 317 coming off and these g...
10/17/2025

Ls 823s for a 6.0L mud bog truck in for porting and rebuild. Been awhile since in the grinder 317 coming off and these going on a N/a set up.

Disassemble
Jet wash and vapour hone
Fully ported and flow tested
New valve guides installed and sized
Multi angle valve job
Resurfaced
New intake valves as the margin was pretty much gone on the old valves.

Customer will assemble with new cam

Have a safe and great weekend guys. Next up Bbc Victor porters casting that are new out of the box.

Sbc engine I finished up a cam swap on pretty much a plain 350 with Pw 180 cylinder heads and a cam upgrade and carburet...
10/10/2025

Sbc engine I finished up a cam swap on pretty much a plain 350 with Pw 180 cylinder heads and a cam upgrade and carburetor upgrade to get away from the TBI set up on a step side chevy. They are pretty limiting in factory form next up a 383 for 98 this one is proving to challenging as it has a 4L60E trans that might just get yanked and a Th 400 installed.

Have a great Thanksgiving guys enjoy the long weekend and stay safe.

Dyno day at Fookes Sbc 350 I just finished with a cam upgrade
10/04/2025

Dyno day at Fookes Sbc 350 I just finished with a cam upgrade

Couple quick carburetor rebuilds and a 2 small atv heads in for rebuilding. Between the field and shop it’s been a busy ...
09/20/2025

Couple quick carburetor rebuilds and a 2 small atv heads in for rebuilding. Between the field and shop it’s been a busy month burning the candle at both ends lots on the go.

Have a great weekend and safe weekend guys

Lefty is done and hard at it doubles as a ride who knew. It’s that time of year if you need something done I will squeez...
08/23/2025

Lefty is done and hard at it doubles as a ride who knew. It’s that time of year if you need something done I will squeeze it in somewhere.

Have a great and safe weekend everyone.

Few little odd things on the go this past week. Composite Hemi intake manifold ported and throttle body matched to the i...
07/25/2025

Few little odd things on the go this past week. Composite Hemi intake manifold ported and throttle body matched to the intake inlet.

A set of new 440 Pw heads sold disassembled check spring heights pressures and guides clearances. Middle spring removed for break in on new flat tappet cam. Again can’t stress how nice the seat work is for entry level aluminum heads. They put Edlebrocks to shame in my opinion for the money.

Have a great and safe weekend guys!

A good friend sent this to me. Love the innovators that paved the road in the industry that weren’t afraid to try someth...
07/16/2025

A good friend sent this to me. Love the innovators that paved the road in the industry that weren’t afraid to try something. One thing that sticks out was self doubt. As real as it was back then it still holds true today. You are always your biggest and worst critic success make that fade away.

Address

Ponoka, AB

Telephone

+14037040055

Website

Alerts

Be the first to know and let us send you an email when Strong Arm Porting & Cylinder Heads posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Strong Arm Porting & Cylinder Heads:

Shortcuts

Share

Category