Electrician DIY

Electrician DIY Welcome to my page

Plumbing professionals reported to the job with this equipment.πŸ˜ƒπŸ˜ƒ
05/08/2026

Plumbing professionals reported to the job with this equipment.πŸ˜ƒπŸ˜ƒ

Will the expansion tank function properly when installed off the relief valve?
05/08/2026

Will the expansion tank function properly when installed off the relief valve?

The image shows a damaged and overheated connection inside an electrical panel. One of the neutral or grounding conducto...
05/08/2026

The image shows a damaged and overheated connection inside an electrical panel. One of the neutral or grounding conductors appears burnt and partially disconnected, which can cause arcing, overheating, voltage instability, or electrical fire.
To repair this safely:
Shut Off Main Power – Turn off the main breaker before opening or touching the panel.
Inspect the Damage – Identify all burnt, loose, or corroded wires and terminals. Heat damage may extend deeper into the conductor.
Remove the Damaged Wire – Cut back the wire to clean copper with no discoloration or melted insulation.
Replace the Terminal or Lug if Needed – Burnt or weakened terminals should never be reused. Install a properly rated replacement connector.
Reconnect Properly – Strip the wire correctly and tighten connections to manufacturer torque specifications.
Check for Overloading – Verify the circuit is not overloaded and the wire size matches the breaker rating.
Inspect the Entire Panel – Heat from one failed connection can affect nearby breakers and bus bars.
Test Voltage and Load – After restoring power, test for stable voltage and ensure there is no overheating under load.

05/08/2026

Ever wonder what’s actually happening inside a leaking water heater? πŸ”πŸ’§
When a tank fails internally, you usually just see a puddle on the floor. But today, we’re performing a full "water heater autopsy" to see the damage for ourselves.

05/08/2026

Radiator leaks often start small, but they’re usually a sign of deeper corrosion or failed seals. Today’s job involved a full teardown and a "sweated" copper replacement to make sure this system stays dry for years to come.
The Fix Breakdown:
Containment First: Never start a radiator job without a proper basin. That old system water is pressurized and messy! πŸ›‘οΈπŸ’§
The Clean Cut: We had to remove the old, pitted copper section to get back to a solid foundation. Precision is key when working in tight spaces against a baseboard. πŸ“βœ‚οΈ
Heat & Bond: A little propane therapy for this copper pipe. There’s nothing quite as satisfying as seeing that solder wick perfectly into a clean joint. πŸ”₯🧼

Upon employing an electrician, this van appears; what would your directives to him be?πŸ˜ƒ
05/07/2026

Upon employing an electrician, this van appears; what would your directives to him be?πŸ˜ƒ

In the process of replacing a ceiling fan in a house built in the 1950s without a ground wire, how should the grounding ...
05/07/2026

In the process of replacing a ceiling fan in a house built in the 1950s without a ground wire, how should the grounding wire from the new fan be handled?

Why do some people exhibit such conduct, and can those involved provide justification for their actions?😲
05/07/2026

Why do some people exhibit such conduct, and can those involved provide justification for their actions?😲

05/07/2026

This image captures a catastrophic failure of a copper-to-iron threaded connection. The massive, cauliflower-like growth of blue-green verdigris and white mineral deposits is the result of years of galvanic corrosion (electrolysis) paired with a slow, persistent leak.

05/07/2026

Most people reach for the chemicals when a sink slows down, but sometimes the only real fix is getting your hands dirty and doing a full teardown.
The Deep Clean Checklist:
The Extraction: We had to chisel out the old strainer just to get to the source. Once it was open, the amount of hair and buildup was enough to clog a sewer main! πŸ§ΌπŸ”§
Contain the Chaos: Never open a drain without a proper basin underneath. That black sludge is not something you want on your cabinet floor. πŸ›‘οΈπŸ“

We hired a deck painting company and the worker spent 3.5 hours pressure washing the deck, leaving debris everywhere and...
05/06/2026

We hired a deck painting company and the worker spent 3.5 hours pressure washing the deck, leaving debris everywhere and potentially damaging the wood. The company claims their method is standard, but I'm worried the wood might be destroyed. Is it possible to paint over this damage or is the wood beyond repair? 25 years ago

Address

Atlanta, GA

Website

Alerts

Be the first to know and let us send you an email when Electrician DIY posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share