Tool_Tips

Tool_Tips Tool_Tips
(5)

10/29/2025

These breakaway screws are perfect to keep in your work vehicle
•
Great for cabinets and closet doors like this
•
Just a quick snip with the side cutter and it’s good to go
•
This newest Makita 18v impact has 4 settings, I usually leave it on high and feather the trigger but it’s nice to have the option
ca

10/29/2025

Do your tools go away clean or dirty?
MDF dust is the absolute worst, just as bad as drywall dust. Once it’s in the truck it’s a pain
•
This little Makita 40v XGT blower won’t replace a big leaf blower but for smaller stuff like this it’s perfect!
ca

10/29/2025

Last year announced a new load lifter air spring kit for the Raptor
•
The Raptor is an amazing truck but the suspension is soft which is needs to be but the rear sags with stuff in the box or a trailer attached
•
Airlift has come up with a cradle that’s separate from the bag so the suspension still has full extension
•
These have up to 5000 lbs of load leveling capacity and can be inflated up to 100 psi
•
Quick install with the mega mod set that has everything you need
•
And yes everything was torqued and each bag had its own valve
•
I use this Makita 40v inflator to fill and deflate the bags

10/29/2025

Do you use CA glue?
It’s so good for preassembling corners like this
•
It has an adhesive and an accelerator.
It’s like 10 seconds for it to hold pieces together
•
Used the New Bosch 18v Brad nailer to fasten all the trims on this basement. One 4ah battery easily did a couple days worth of trim


10/29/2025

The Milwaukee MX Fuel Gen 2 power cutter
•
This was my first time running it, as good as the Gen 1 was the Gen 2 is more powerful and smoother. I also saw what seemed to be a much longer runtime and no battery overheating with the New Forge battery
•
Even with the water turned on the saw won’t let water run through till the blade is spinning, I’m a fan of that feature.

10/29/2025

This Festool Exo suit doesn’t make you stronger but it sure can help you work longer and creates far less stress on you body
•
We’ve used it for doing ceiling work, especially sanding the ceilings with the Planex
•
It is a bit bulky and that compressor is a bit annoying but having shoulders not ache the next morning is well worth it
•
Have you got to try one of these?


10/27/2025

Even if the Makita wasn’t faster I’d still choose it because it has less vibration.
•
If you have used a reciprocating saw for a long period of time you know how hard it can be on your hand/arm
ca

10/27/2025

Check out this 1000 series mower
•
It has a 22” composite deck that has a 10 year warranty. It lightens up the mower more for maneuverability
•
It’s self propelled and has 3 cutting speeds as well as lights on the front.
Multi-Blade Cutting System has an upper blade and interchangeable lower blades to customize your cut
•
You can fold it up and store it up against a wall in your garage or shed to save space
•
With two batteries installed it puts out 10.6 ft pounds of torque with a blade speed of 3200 rpm. Much more powerful and faster than gas.

10/27/2025

Make it your own!
•
I like everything to have its place, I’ve been holding off to long on building this.
•
I’ve added the and the CargoGlide this year to my truck which has been a great addition
•
Now I’m started to fine tune this setup with some shelving and a bunch of other stuff that’s on the way
•
I’m building it all around the Makita MAKTRAK storage system
•
Nice to also have a way to store the Crescent site runner too

10/27/2025

Sound Up!!!! 🔊
The New Makita 18v Impact is smaller, faster but louder than the Makita 18v soft impact
•
These soft impacts are great for working in areas that are noise sensitive or if you want a smoother feel
•
It has fluid inside to dampen the sound and run smoother

•
What would you choose?

10/27/2025

This customer wanted a cover for the water meter, normally we build a bench but they asked if we could do some shelves
•
It took 2 pieces of MDF and I used some left over trims
•
Just some wood glue and the Bosch 18v brad nailer to put this one together


10/27/2025

Still can’t believe how well this Exo T 22 tool balancer works
•
It’s pretty much a backpack crane that helps take the weight off the tool
•
This setup runs on just one of their Nuron batteries which runs any other tool in the Nuron lineup

Address

1547 Sardis Sta
Dallas, TX
75201

Telephone

+13124626463

Website

Alerts

Be the first to know and let us send you an email when Tool_Tips posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Tool_Tips:

Shortcuts

Share

Category