Williem World

Williem World Waiting for Succues

Master L**e Tech here, 2012 Kia Sorento EX trying to remove a stubborn 17mm suspension bolt located above the front left...
09/12/2026

Master L**e Tech here, 2012 Kia Sorento EX trying to remove a stubborn 17mm suspension bolt located above the front left lower control arm, but it refuses to budge. I've already soaked it with PB Blaster, tried multiple breaker bars, and even used a DeWalt 20V MAX impact wrench, but nothing has worked.

After repeated attempts, the bolt head is starting to round off, so im hesitant to keep forcing it and make the situation even worse. I'm looking for advice on the safest and most effective way to remove the seized bolt before it becomes completely stripped.

Can someone please tell me exactly what this piece is called? Need to replace it asap. 2016 dodge 3500
09/12/2026

Can someone please tell me exactly what this piece is called? Need to replace it asap. 2016 dodge 3500

1990 Mustang driver-side rear drum brake issue Working on the rear drums on my 1990 Mustang 5.0 and I’m stuck on the dr...
09/12/2026

1990 Mustang driver-side rear drum brake issue Working on the rear drums on my 1990 Mustang 5.0 and I’m stuck on the driver side. The primary shoe, left side in the photo, keeps getting pulled upward. I can push it back down where it looks like it should sit, but as soon as I let go, the spring pulls it right back up.
I installed the springs the same way they were before I took it apart, so I’m not sure what I’m missing.
Anybody see anything obvious that’s installed wrong or know what would cause the shoe to keep riding up..?

Does anyone know how to get this wheel lock key onto a breaker bar? 🤔Trying to swap out my brake pads, but I've run into...
09/12/2026

Does anyone know how to get this wheel lock key onto a breaker bar? 🤔

Trying to swap out my brake pads, but I've run into a roadblock. I have this weird key for the wheel lock, but I'm not sure how to adapt it to my breaker bar.
Has anyone seen this type of setup before? Any tips on how to get this to work? 🔧

What’s the best way to break this drain plug loose without cracking the housing?Oil filter drain on my 2GR-FE is stuck t...
09/08/2026

What’s the best way to break this drain plug loose without cracking the housing?

Oil filter drain on my 2GR-FE is stuck tight. Looks like the previous shop just torqued it down way too hard instead of using the proper filter housing tool.

I’ve got the housing out so I can work on it at the bench, but that drain plug isn't budging. Anyone got any tricks to get this loose without damaging the housing? 🚰

Doing my lower ball joints and I’m stuck on this axle nut. I’m pretty sure the last shop used an impact to tighten it, b...
09/08/2026

Doing my lower ball joints and I’m stuck on this axle nut. I’m pretty sure the last shop used an impact to tighten it, because this thing is absolutely refusing to come off. My impact is rated for 280 ft-lbs, but it hasn’t even budged. I’ve got a torch if that would help, but I’m not sure if heat is the right move here. Any tips or tricks for getting this thing loose without damaging anything?

So, a 1/2-inch ratchet is fine, then? 😆
09/08/2026

So, a 1/2-inch ratchet is fine, then? 😆

🏁 CONSISTENCY WINS RACES.Compressed Air Supercharging gives you precise, controlled air delivery when you need it, helpi...
09/08/2026

🏁 CONSISTENCY WINS RACES.

Compressed Air Supercharging gives you precise, controlled air delivery when you need it, helping racers fine-tune their setup and put the power to work.

🎯 Control it. Tune it. Repeat it.

Compressed Air Supercharging
built for racers chasing the next win.

We can’t get the rotor off. Any advice? We’ve already tried a hammer, WD-40, penetrating oil, and even heat, but this th...
09/07/2026

We can’t get the rotor off. Any advice? We’ve already tried a hammer, WD-40, penetrating oil, and even heat, but this thing refuses to move even an inch. 😩 It looks like it’s practically welded itself to the hub from years of rust and corrosion. We’ve been beating on it with no luck so far. Is there a trick we’re missing, or is it time to bring out the bigger tools? Any suggestions before we make things worse? 🔧😅

Need a little Tecumseh help. I’m working on a 640350 carburetor. Got it all cleaned up and put back together. However wh...
09/07/2026

Need a little Tecumseh help. I’m working on a 640350 carburetor. Got it all cleaned up and put back together. However when i add gas to the line it’s leaking out the bottom of the nut holding the bowl. The jet nut is what i call it has a hole all the way through. Briggs don’t have this design.
Logically it should leak. It’s a got a hole in the center of the nut.
Surely this isn’t correct. What could be the issue? Gas is pouring out of it. Float issue? Needle seat?(i used a red Briggs one and it fit)
Help!

Address

82 Rutgers Slip
New York, NY
NY10002

Website

Alerts

Be the first to know and let us send you an email when Williem World posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category